Concrete Calculator
Use this concrete calculator and estimator to figure concrete for a slab, pad, footing, or column before you buy. Enter your dimensions below and switch tabs for the project type you're pouring. You get cubic yards, 60lb and 80lb bag counts, and an estimated cost.
Understanding the inputs
- length
- The longer run of your pour, in feet. For a footing, this is the total length of the trench.
- width
- For a slab, the shorter side in feet. For a footing, the trench width in inches; footings are usually narrower than they look, often 12-16 inches.
- thickness
- Most residential slabs (patios, walkways, garage floors) are 4 inches thick. Driveways and footings are usually deeper; check your local building code before pouring.
- diameter
- The width of the column or post hole, in inches. Measure across, not around.
- height
- How tall the column or post will stand above (or be buried below) grade, in feet.
- quantity
- How many identical columns or posts you're pouring. The total scales directly with this.
- price
- Ready-mix delivery price per cubic yard varies by region and order size; $150/yd is a reasonable national placeholder. Call a local supplier for an accurate quote.
Concrete weight by type (approximate, per cubic yard)
| Concrete type | Weight per cubic yard |
|---|---|
| Standard mix | ~4,050 lbs |
| Lightweight mix | ~3,000 lbs |
| High-strength mix | ~4,200 lbs |
Frequently asked questions
How do I figure concrete for a slab?
Multiply the slab's length by its width (in feet) and by its thickness (in feet, so 4 inches is 0.33 ft) to get cubic feet, then divide by 27 to get cubic yards. A 10 ft by 10 ft slab that is 4 inches thick is 33.3 cubic feet, or about 1.23 cubic yards. This calculator does the math for you and adds bag counts and a cost estimate. Setting fence posts instead? Use the post hole concrete calculator. Mixing by hand? The sand and cement calculator splits a batch into cement, sand and gravel.
How much does a concrete slab or pad cost?
Multiply the cubic yards by the price per yard. At the $150 per yard placeholder used above, a 10 ft by 10 ft slab at 4 inches (about 1.23 cubic yards) is roughly $185 of ready-mix concrete. That covers the concrete only. Forms, rebar, base gravel, finishing, delivery fees and short-load charges for small orders come on top, so use your supplier's quote for the real number.
How much concrete do I need for a 650 square foot slab?
At 4 inches thick, 650 square feet is 650 x (4 / 12) = 216.7 cubic feet, or about 8 cubic yards. At 5 inches it is about 10 cubic yards, and at 6 inches about 12. Enter the length and width above for your own slab, and order a little extra to cover uneven ground and spillage.
How much does a yard of concrete weigh?
One yard of concrete (a cubic yard of standard mix) weighs approximately 4,050 pounds (about 2 tons). The exact weight depends on the mix: lightweight mixes run closer to 3,000 lbs/yd, while high-strength mixes can exceed 4,200 lbs/yd. See the comparison table above for common mix types.
How many 80lb bags of concrete are in a cubic yard?
An 80lb bag yields about 0.6 cubic feet of mixed concrete, so it takes roughly 45 bags to make one cubic yard (27 cubic feet ÷ 0.6). This calculator converts your volume into both 80lb and 60lb bag counts automatically.
How thick should a concrete slab be?
Most residential slabs, patios, walkways, and shed floors are poured 4 inches thick. Driveways that see vehicle traffic are typically 5-6 inches, and footings are usually deeper still. Always confirm the required thickness against your local building code before pouring.